The tough duty is going to be the 50 mph trade winds blowing the trees. It's going to be interesting ... Hopefully the trades are a little less active on Monday.
Good sawing,
Tim Ard
- Posted using BlogPress from my iPad
Location:Waimea, HI
A chain saw applications and safety forum for professional and occasional operators by Tim Ard
Location:Waimea, HI
I have come to a conclusion today that it is much harder to keep from getting stuck in logs and limbs under pressures and twist with a small narrow saw bar and chain.
Small saws, with narrow chain, really make it easier to get a saw stuck when cutting and limbing. The wider kerf cuts of .325" pitch and .375" (3/8") pitch saw chain seem to stay out of binds much better.
Is it the width of the kerf? Relationally the pressure that is applied when the kerf closes under force? Is the wider kerf affording more reaction time? Those shouldn't be the cause or relief of the situation.
I know something played a roll today. I am accustomed to a larger, more powerful saw and wider chain kerf. Using a small saw today I don't think I could make a cut without binding.
Maybe I have just gotten spoiled to power.... The weight of the saw is more and that has a negative effect on the operator and long term operation, but the power I think is what keeps the chain spinning and reduces the pinches.
What do you think?
It could be my planning process... I was off somewhere!
Good Sawing,
Tim Ard
One thing networking with Facebook has done for me is to reconnect with some folks that have made my life and career what it is today.
This morning I received a message from someone whom I haven't heard from in years. My auto shop teacher from high school, "Doc" Lamb. Doc was a great instructor and mentor. I wanted to have a career in auto repair, especially racing, and Doc kept me interested and focused.
One summer he asked if I would like to work on the bus maintenance program. He used to have all the county school buses, that needed cleanup, repaint and tune-ups, brought over to the shop at the high school and he would handle the work. He'd have selected students come in and work for a summer job. I was one of those.
The summer of 1974 I worked on the buses and we finished a little early. Doc had been contacted by several businesses wanting to find summer help and future employees from his students at the school. One of those companies was Henningsgard Equipment in Marietta, GA. Doc suggested me for the job to finish out the summer there. That was my first time working with small engines other than a couple lawnmowers and a chain saws at home with my Dad. I fell into the work, enjoyed it and soon took another job working on mowers and saws in Hiram, GA after I graduated in 1975.
So you could say that Doc Lamb was the one that got me started in all this ChainSaw Stuff! Thanks Doc for doing that - it has been a good road to travel!
You know, teachers and instructors do a lot to mold and develop futures... few too many times they are thanked and recognized for that.
Good Sawing!
Location:Hilo Hawaii
Run Check
By Tim Ard, Forest Applications Training, Inc.
How should a saw perform once it is started? What do you look for to make sure it is going to run and do the Job you need it to?
Five areas to check out to make sure the saw is performing as it is designed:
1. Clean Air Filter - you must make sure the chainsaw nose (filter) is breathing properly. If the filter is restricted the airflow for proper adjustment will be low and cause smoking, low power and poor running results.
2. High Speed Levels to Flutter - let the saw warm to running temperature before attempting to determine if high-speed settings are correct. This will take a couple minutes or so after starting to accomplish. Then hold the saw at wide-open throttle for a few seconds. The rpm should come up to a full throttle position and then level off. It sounds kind of like a flutter or a slight blubbering tone. The flutter sound must be in any two cycle high speed run to make sure you have sufficient lubrication and fuel for the engine. A digital tachometer can be used to check if the run is set to design parameters suggested by the manufacturer. A tachometer will only tell you when an engine is in adjustment - it won't however tell you when it's out of adjustment. An engine can show within the design a maximum RPM setting that’s within specification but can have an air leak or other engine problem and can still be running in a lean state. That's where the operator must understand a two-cycle flutter and make sure the saw at top end is fluttering. If not major damage to the engine can and most likely will take place. The high-speed setting is done with the H screw on the carburetor.
3. Chain Stops at Idle - now bring the engine back to idle for the next observation. We want to make sure that the engine is at idle for a couple reasons. The first is safety because you do not want to be walking around with a chainsaw where the chain doesn't stop turning at idle. This also indicates that the engine is idling low enough, if the saw chain stops, to disengage the clutch mechanism and let the low speed fuel circuits in the carburetor take over. When the chain turns at idle you adjust the T or LA screw to raise or lower the RPM to disengage the clutch.
4. Idles In All Positions - now that the chain is stopped and the saw is at idle, the saw should idle in all positions until it runs out of fuel. If the saw is getting too much fuel at idle it will puddle up in the crankcase area and as soon as you roll it over it will flood the port and the engine will stall. The L screw on the carburetor adjusts this scenario. In this case you would close the screw slightly clockwise to reduce the fuel flow.
5. Accelerates Without Hesitation - next the acceleration should be checked. Open the throttle quickly and the RPM should come up without hesitation. If the engine hesitates before quickly rising to wide-open throttle, the L screw on the carburetor should be opened counter-clockwise to allow more fuel flow. It takes fuel to create the power to rotate the engine.
You should remember that you could damage the saw engine quickly if you do not run it properly adjusted. I hear often that supervisors and shops do not want the operator to have access to a screwdriver, nor to adjust the screws. They state that they don't want the saw blown-up from someone who doesn't know how to properly adjust the screws. I agree, but I have said for years that I think I see as many saws and trimmers blown up from lack of adjustment as I have adjustment. If the operator doesn't know when it is out of adjustment they just run it. You do not have to have a screwdriver yourself however to adjust the saw. If you know when it is out of adjustment you can simply take it to someone who does.
Think about - anytime you turn a carburetor screw to the right, clockwise, you take a chance of causing engine damage. You remove fuel and lubrication with a clockwise turn of the screw.
Operators should all be aware of how to check the run of any two-cycle piece of equipment. If they are going to work safely and productively with the machine it must be in tune...
More information on carburetor adjustment can be found in our ForestApps eBook available from www.BarnesandNoble.com and from the eStore at www.ForestApps.com.
Check out the articles on carburetion and fuel under the info/articles link on the homepage. Good Sawing...
Auto Tune….
By Tim Ard, Forest Applications Training, Inc.
Manufacturers have been talking about it for a while but it might be just in time to help curb some (not all) of the fuel issues with ethanol base gasoline. Husqvarna has introduced a new version of the 576xp saw with a new Auto Tune carburetor. It’s not really a fuel injection system but it is a smart carburetor that’s a very close twin. No manual adjustments, the carburetor makes automatic adjustments of the fuel and air ration going into the engine with an electronic control system. It also compensates for air filter obstruction to help minimize rich runs and loss of power.
This Auto Tune system should help some with the issues around ethanol fuel supplies. Ethanol added fuels have a larger molecule to transport and also attracts moisture (water) at the molecule so it in effect requires a larger hole (carburetor jetting) to offer enough fuel to maintain power and RPM control of your saw. Some carburetors today do not have sufficient adjustment capabilities to handle the larger ethanol fuel structure.
Take for example if you have a saw adjusted to spec, at less say 13,000 rpm. The engine is running great and you have plenty of lubrication taking place because you have a proper oil to gas mix ratio adjusting in. It’s all good….
Now you buy fresh gas at a local station and mix in your oil to requirements. The new fuel you purchased however has 10% or more ethanol in its formulation. If you do not change the carburetor adjustments of air and fuel entering your engine you have most likely leaned out the run of the saw because of the added fuel flow requirement of the ethanol, which you are not getting, and also your lubrication is minimized because of this fuel restriction. Leaning the lubrication and over speeding the design. Not good….
The Auto Tune carburetor will now step in to do its job. It allows more fuel in to properly mix with the air through the filter and voila – proper running engine. The only thing to consider now with the ethanol fuel is the water accumulation and the deteriorating effects on your saws rubber and internal parts. Which these effects are somewhat minimal to the seizure costs.
I hope we see many more of these techno changes in the near future and even some upgrade carburetors available for existing equipment – that would be nice. This would correct a great deal of the run problems showing up in the field. Until then – seek out a source for TruFuel or a gas without ethanol to do your mixing… or I recon you could just buy a new Husqvarna 576xp.
Good Sawing,
Tim Ard
http://www.husqvarna.com/us/homeowner/products/chainsaws/576-xp-w-autotune/
Last Saturday at the Rugged Quarter in Trussville, AL, Rob Lagerstrom, Bill Fyfe and I worked on the completion of the RDT eVideo and the Storm Damage eVideo.
We had previously shot most of the RDT video. We only had to add an intro and then a few defining shots and shoot the Run Check outline and discuss a bit about fuel. It went quickly and I think its up to Rob on the edit table to have it ready to go.
We then went out to the field to shoot a large broken Hickory Tree that had fallen, broken over the motorcycle trail below the entrance road. This thing is about 25ft to the break point and then bent over back to the ground with lots of weight. We took info on it and I thought I had a plan. It was working until one of the hinges in the top held too well. I had it in the wrong position and too thick. Not a safety issue, just had to go to plan B. But the effect for the eVideo was over for that scenario. You will like this one...
We then hung up a tree and planned the takedown. Looked at SpringPole's and a few limbing cuts. All the rest went well.
I think you are going to be impressed with these eVideos when they are ready.
Thanks Rob and Bill for a great day and future AWESOME eVideo training tool.
Good Sawing,
Tim Ard